HRC Fuse Link and Fuse Base

Application : HRC Fuselinks are designed to meet the requirements set for modern industrial installations & electrical power plants of their breaking capacity is sufficient even for the highest level which occurred in practice.

Current Limiting Effect : Fuselinks are current limiting type resulting in reduced electromagnetic stress to protect device adequately. A current limiting protective device breaks off short circuit current is less than one half cycle is more before it attains its total peak prospective current. Thus unfavourable effects of the short circuit on the switchgear are prevented.

SALIENT FEATURES :

• Compliance to performance and dimensional requirement of Indian and International standard
• IS : 13703 (1993), IEC 269 (Pt. I and II) : 1986.
• Rated short circuit capacity at 80 KA. ~ 415V, 50 Hz.
• Fuse links are designed of very low Power loss for cool running and energy saving in power Installations.
• Lower cut-off current reduces electromagnetic stresses for which device is protected adequately.
• 2 Low I t let through energy reduces thermal stresses, Fire risk & damage to equipments.
• There is no emission of gas or flames in operation.
• Breaking range & utilisation category "gG".
• Idealy suitable for back up protection to motor startors against short circuit faults.
• Bolted type - upto 125A to 200A SDV-FP

We have two types of hrc fuse base.

1. Close type fuse carrier

2. Open type fuse base

in close type fuse carrier we are making the ratings of 20amps. 32amps. 63amps and 125amps. In front connection and busbar connection

in open type fuse base we  are making the ratings of 125amps. 250amps. 400amps and 630amps. In bakelite and dmc moulded.

We are rated among the reliable Bakelite Moulded close type HRC Fuse Base Manufacturers and Exporters of the HRC Fuse Base located in Delhi. These HRC Fuse Bases are made using the best quality material. We offer the HRC Fuse Base at the market leading rate to the customers. Ensuring reliable performance and long life, the HRC Fuse Base, which we offer, is easy to attach.

These fuse bases and holders conform to IS : 13703 & IEC : 60269 specification.

HRC Fuse Base Open 125 A, 250 A, 400 A & 630 A

Moulding (Casing)
The Bases are manufactured from high grade Dough Moulding compounds (DMC) / Bakelite. These are non-inflammable, non-hygroscopic and with hard glossy black finish.

Contacts
Current carrying parts of the holders are made from precisely pressed copper / brass material and have extruded brass base contacts. These are mounted on moulded seats to ensure perfect alignment. The current carrying parts of the fuse bases are electroplated with silver to ensure long life, non-deteriorating contact surface for high efficiency mating.

Terminals
Copper/ Brass terminals are used for direct cable termination in case of enclosed type Fuse Holders and through Cable lugs for open type Fuse Bases complete with cable holding fasteners.

The Bakelite Moulded and DMC Moulded HRC Fuse Carrier, which we offer, is manufactured using the best quality material. Conforming to several quality standards, these HRC Fuse Carriers are packed properly using the best-grade packing material, ensuring their safety in transit. We are among the dependable Manufacturers and Exporters of the HRC Fuse Carrier from Delhi. We are among reputed fuse carriers exporters.

Availability : Close Type Fuse Holder for 02A to 125 A Bolted Type Fuse Link, Bakelite Fuse Carrier 20A, 32 A, 63 A & 125 A

Contacts
Current carrying parts of the holders are made from precisely pressed copper / brass material and have extruded brass base contacts. These are mounted on moulded seats to ensure perfect alignment. The current carrying parts of the fuse bases are electroplated with silver to ensure long life, non-deteriorating contact surface for high efficiency mating.

Backup clips
Backup pressure clips have been precisely formed from from Phosphor Bronze / Spiral Steel materials to ensure perfect mating of male and female parts, for long time.

Terminals
Copper / Brass terminals are used direct cable termination in case of enclosed type Fuse Holders and through Cable lugs for open type Fuser Bases complete with cable holding fasteners.